Nova-tech GC Indicator Manual de usuario Pagina 1

© Adam Equipment Company 2010 Adam Equipment GC INDICATOR (P.N. 3056610550, Revision C6, August 2010) Software Rev 2.18 and up

P a g e 8 © Adam Equipment Company 2010 4.0 KEY DESCRIPTIONS Keys Functions [0-9, .] Numeric entry keys, used to manually e

P a g e 9 © Adam Equipment Company 2010 5.0 DISPLAYS The scales have three sections. These are “Weight”, “Unit Weight” and “C

P a g e 10 © Adam Equipment Company 2010 5.2 UNIT WEIGHT DISPLAY This display will show the unit weight of a sample. This val

P a g e 11 © Adam Equipment Company 2010 6.0 OPERATION NOTE: GC-a Scales only SETTING THE WEIGHING UNIT, lb or kg The scale w

P a g e 12 © Adam Equipment Company 2010 6.2.1 Preset Tare • The user can enter a preset tare value if the display is at zero

P a g e 13 © Adam Equipment Company 2010 • If the scale is not stable, the calculation will not be completed. If

P a g e 14 © Adam Equipment Company 2010 6.3.4 Manually Accumulated Totals • The values (weight and count) shown on t

P a g e 15 © Adam Equipment Company 2010 7.0 USER PARAMETERS The parameters are set to customise the scale to suit the weig

P a g e 16 © Adam Equipment Company 2010 7.1 SETTING OF PIN • Display will show “F2” “Pin”. This parameter allows set

P a g e 17 © Adam Equipment Company 2010 8.0 CALIBRATION • The GC scales are calibrated using metric weights and GC

© Adam Equipment Company 2010 Easy Reference: Model name of the indicator/scale: Serial number of the unit: Software revision number

P a g e 18 © Adam Equipment Company 2010 9.0 RS-232 INTERFACE The GC Series are supplied with a RS-232 bi-directional

P a g e 19 © Adam Equipment Company 2010 Data Format-Normal Output: Data Format- Memory Recall Print: <lf><cr> &l

P a g e 20 © Adam Equipment Company 2010 Data Format- Continuous Print: In other languages the format is the same but

P a g e 21 © Adam Equipment Company 2010 9.1 INPUT COMMANDS FORMAT The scale can be controlled with the following commands.

P a g e 22 © Adam Equipment Company 2010 9.2 RS-232 SETUP The RS-232 interface uses parameters set by the user for language,

P a g e 23 © Adam Equipment Company 2010 The scale will perform the following functions depending on the Accumulation and Print

P a g e 24 © Adam Equipment Company 2010 9.3 REAL TIME CLOCK SETUP The Real Time Clock (RTC) is used only for the RS-232 out

P a g e 25 © Adam Equipment Company 2010 9.4 AUTO SLEEP FUNCTION This function may be enabled or disabled by the user. If enab

P a g e 26 © Adam Equipment Company 2010 10.2 BACKLIGHT FOR LCD • The backlight of the LCD can be set to be- “1”: ON at all t

P a g e 27 © Adam Equipment Company 2010 11.0 ERROR CODES During the initial power-on testing or during operation, the scale

P a g e 1 © Adam Equipment Company 2010 CONTENTS 1.0 INTRODUCTION...

P a g e 28 © Adam Equipment Company 2010 12.0 SERVICE PARAMETERS 12.1 USING “0000” TO ENTER THE CALIBRATION PARAMETER • Pre

P a g e 29 © Adam Equipment Company 2010 12.1.1 F1 -CALIBRATION To enter the calibration parameter, press the [Tare] key when

P a g e 30 © Adam Equipment Company 2010 12.2 USING “2006” TO ENTER THE SERVICE PARAMETERS Before setting the parameters for u

P a g e 31 © Adam Equipment Company 2010 The parameters available are: “F1” “Unit” Default Weighing Unit “F2” “dPP”

P a g e 32 © Adam Equipment Company 2010 • Press the [U.Wt./Units] key to change the value. Select from 0, 0.0, 0.

P a g e 33 © Adam Equipment Company 2010 • The display will tell you to add the second weight to the scale: “LoAd 2 “ 100

P a g e 34 © Adam Equipment Company 2010 12.2.8 F8 –ADC COUNTS • To enter this parameter, press the [Tare] key when “F8” is

P a g e 35 © Adam Equipment Company 2010 12.2.11 F11 –ZERO TRACK SETTING • This parameter allows the amount of zero

P a g e 36 © Adam Equipment Company 2010 13.0 REPLACEMENT PARTS AND ACCESSORIES If you need to order any spare parts and acces

P a g e 37 © Adam Equipment Company 2010

P a g e 2 © Adam Equipment Company 2010

P a g e 38 © Adam Equipment Company 2010 14.0 SERVICE INFORMATION This manual covers the details of operation. If you have

P a g e 39 © Adam Equipment Company 2010

P a g e 40 © Adam Equipment Company 2010 15.0 WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour

© Adam Equipment Company 2010 Manufacturer’s Declaration of Conformity This product has been manufactured in accordance with the harmonised Eur

© Adam Equipment Company 2010 ADAM EQUIPMENT is an ISO 9001:2000 certified global company with more than 35 years experience in the pro

P a g e 3 © Adam Equipment Company 2010 1.0 INTRODUCTION • The GC series provides accurate, fast and versatile parts counti

P a g e 4 © Adam Equipment Company 2010 2.0 SPECIFICATIONS INPUT SECTION Load Cells Up to 4, 350 ohm load cells Minimum 87 oh

P a g e 5 © Adam Equipment Company 2010 Overall Dimensions (wxdxh) 260 x 110 x 170mm 10.2” x 4.3” x 6.7” Net Weight 1.1 kg / 2

P a g e 6 © Adam Equipment Company 2010 3.0 INSTALLATION 3.1 UNPACKING This indicator must be connected to a load cell platf

P a g e 7 © Adam Equipment Company 2010 3.3 CONNECTION This indicator must be connected to a load cell platform and calibrat